- 18%

Truck Ad-blueobd2 Emulator for VOLVO livraison gratuite

En stock. Histoire 89 vendu. Numéro d'article: No.SH35

Dernier prix: 28.00
Achat immédiat: 22.95 -18%
Livraison:
Livraison gratuite Poste Ordinaire Service    Délai de livraison estimé: 10-20 jours de travail. Détails
Poids:
0.2KG
Paquet:
15.5cm*10cm*5cm     ( Pouce: 6.1*3.94*1.97 )
Résultats:
Retour de remboursement dans 7 jours, l'acheteur paie les frais de retour. Lire les Détails »

Fichiers de téléchargement associés


Description du produit

Ad-blueobd2 Emulator Box designed to disable Ad-Blue system used in trucks, buses and other heavy vehicles with EURO 4/5 exhaust emission rates Ad-Blue Emulator Box bypasses electronic module of the Ad-blue system on vehicle.

VOLVO Ad-blueobd2 Emulator description:

Ad-blueobd2 Emulator Box designed to disable Ad-blue system used in trucks, buses and other heavy vehicles with EURO 4/5 exhaust emission rates Ad-blue Emulator Box bypasses electronic module of the Ad-blue system on vehicle.
Its very easy to fit Ad-blueobd2 Emulator Box to any truck or bus equipped with Ad-blue system and it will override Ad-blue system instantly, it will stop the usage of Ad-blue liquid. Ad-blue Emulator Box disables
Ad-blueobd2 system electronics gently so there will be no power loss of the engine or any warnings on the dashboard and in diagnostic system.

This device works without interfering to work of other electronic systems of the vehicle. Ad-blueobd2  Emulator Box has a wide range of supported vehicle models and there is only one version
of emulator for all supported trucks, just upload the necessary program to the Ad-blue Emulator Box and you can install it on any supported truck.

Installation of VOLVO Ad-blueobd2 Emulator:

The connections details diagram and wire colours refer to VOLVO FH16 Year 2008, but the main procedure of the minusblue module does not vary. Before proceeding make sure no faulty codes are memorised in the original
ECU, AD-BLUE liquid is higher than the reserve level and the truck batteries are disconnected from the system.

Wiring:

5 conductors:

1) RED(+15). To be connected to a 24V source enabled when the engine key is in the ON position. This connection will supply power to the minusble Module when the engine key is on(dashboard on).

2) BLACK(0V). To be connected to an earth.

3) GREY(+30). To be connected to a 24V supply always available to the existing Ad-blue system (25A protection fuse and the Ad-blue system).

4) WHITE(CAN H). To be connected to CAN H of the system.

5) BROWN(CAN L). To be connected to CAN L of the system. The connections must be made under the box of the connectors located on the chassis.

Activation :

The minusblue module and the original Ad-blue module CANNOT both be activated at the same time, the GREY ACTIVATION WIRE(+30) is to enable the minusblue module working. It is important to connect the GREY ACTIVATION WIRE(+30) to a 24V source always available(battery), moreover, the soldering operation must be done between the 25A fuse and the existing Ad-blue module.

If you want to stop and exclude the original Ad-blue module from working, all that needs to be done is to remove the 25A fuse before starting the engine. The minusblue module will automatically be activated. To re-instate the original Ad-blue module, all that needs to be done is to reinstall 25A fuse before starting the engine. The minusblue module will automatically be de-activated.

Self-learning:

When the minusblue module is fully connected to the electrical circuit of the original Ad-blue module, and after identification of the 25A fuse controlling the power feeding to the original Ad-blue module the truck batteries can be Re-connected.

The minusblue module aquires the inputs from the CANBUS the first time the dashboard is turned on(key on but engine still off).

1) Make sure the 25A fuse is inserted.

2) Turn on the dashboard(key on) and verify that the red led is on.

3) After approx 1 minute the red led will turn off and the green led will Turn on.

4) Switch off the dashboard(key off).

After this procedure the minusblue module will be activated whenever the dashboard is turned on(key on).

The result will be:

1) If the 25A fuse is installed the original Ad-blue system will be working. Both red and green leds will be on.

2) If the 25A fuse is not installed the original Ad-blue system will not be working and the minusblue module will be activated. Both red and Green led will be flashing.

NOTE: ALL THE OPERATIONS WITH THE 25A FUSE MUST BE DONE WITH THE DASHBOARD SWITCHED OFF(KEY OFF).

LED FUNCTION ON - OFF

KEY OFF:- RED OFF, GREEN OFF - NO POWER FEEDING.

KEY ON:- RED OFF, GREEN OFF - TRUCK NOT SELECTED.

KEY ON:- RED ON, GREEN OFF - WAITING FOR SELF-LEARNING.

KEY ON:- RED OFF, GREEN ON - LEARNING COMPLETED.

KEY ON:- RED ON, GREEN ON - DATA SAVED, MODULE NOT ACTIVATED.

KEY ON:- RED PULSE, GREEN PULSE - DATA SAVED, MODULE ACTIVATED
 

When this box connected - Ad-blueobd2 system of the truck would be fully emulated, no errors related to Ad-blueobd2.

The box can be fast and easy installed to truck. You can disconnect it, reset and install into another truck

 

Attention: S'il vous plaît laissez votre numéro de téléphone pour l'expédition lorsque vous effectuez le paiement pour ce produit sur notre site Web.

Pour toute question, veuillez nous contacter à:

Email: Sales@AutoObdTool.fr
Skype: Autotool.fr
Whatsapp: +86 18205950686

Scan AutoOBDtool Code QR pour commander n'importe où et n'importe quand par téléphone portable.




Les clients ayant consulté cet article ont également consulté